Powerbass pb2.120

3000w amplifier 2 channel

• 2 Ohm Stable
• 3000w
• 2 channel
• 1500w per channel
• Trimode Operation
• Bridgeable 2/1 Channel Mode
• Adjustable Input Sensitivity
• Infinitely Adjustable High Pass and Low Pass Filter
• Variable Bass Booster
• Thermal/Short-circuit/Overloading Protection
• Automatic switching On/Off via Car Radio
• Mute Circuit for suppressing switch on crackle interference
• High Efficient Mosfet Power Supply

• 2 Ohm Stable
• Tri-mode Operation
• 2/4 Channel Selection Circuit
• Adjustable Input Sensitivity
• Infinitely Adjustable High Pass and Low Pass Filter
• Variable Bass Booster
• Thermal / Short - circuit/ Overloading protection
• Automatic Switching On/Off via Car Radio
• Power on and Protection LED Indicators
• Mute Circuit for suppressing switch on crackle interference
• High Efficient Mosfet Power Supply

Arachnid Amplifiers are the next step in performance and value. Taking advantage of our tried and true class A/B Full Range and improved efficiency Class D Monoblock platforms, Arachnid Amplifiers continue down the road of reliability and longevity you know well. 

• 2-ohm Stereo & 4-ohm Bridged Full Range Operation
• Military Grade PCB w/ PWM MOSFET Power Supply
• Direct Short, Thermal, & Overload Circuit Protection
• High/Speaker Level & Low Level/RCA Input
• 200mV-6V Low Level RCA Input
• Pre-Amp Low-Level RCA Outputs (Select Models)
• 4g Power Wire & 8g Speaker Wire Outputs
• Variable 12dB High & Low Pass Crossovers
• 12dB Bass Boost Increases Low Octave Harmonics

A Perfect Solution

The DXA250.4 Four-Channel Amplifier is a perfect solution for all of your door speakers, or a bumpin’ three-way system for a two seater.

Use FIT™ (Fail-Safe Integration Technology) to install this amp in any ride – with or without a factory radio. For even more bass, use KickEQ™ for up to 12dB of extra bump!

This DX amplifier delivers as much as 60 watts per channel (4 channels driven), or 125 watts into two sets of bridged channels. See below for more details.

DPower 4

D CLASS FOUR CH AMPLIFIER

Tens of thousands have relied on V-Power amplifiers for dependable, quality power. Now in their fourth generation, V-Power amplifiers carry on this heritage and prove that playing strong never looked our sounded better. Yes, it is possible to improve upon a good thing.

Overview

• Total Max Power: 640 W
• 75W RMS x 4 (2Ω, 14.4V, ≤1% THD+N)
• 50W RMS x 4 (4Ω, 14.4V, ≤1% THD+N)
• Same power in a 40% smaller chassis
• Evolution to Class D digital platform
• New snap-on terminal covers for easy installation

Raising the Bar

The new V-Power products are now Class D digital amplifiers, resulting in a huge efficiency gain versus their predecessors without draining your battery or your pockets. Class-D provides continuous clean power to your speakers, operating at 80% efficiency far greater than conventional Class A or B amplifiers. Translation: Enjoy cleaner bass, even during extreme power demands.

Big Power, Small Package

V-Power amplifiers are known for their compact size, but don’t underestimate their power capacity. Although they have a 40% smaller footprint than their predecessors, they produce the same amount of power as before. Get the power you need, even if you have limited installation space.

Non Shut-Down Design

Even if you pound your music for a long time, these amps won’t shut down. They use a Thermal Management Processor to make sure the heat level never gets too high. No distortion, no interruptions!

Dual Feedback Modulation

Dual internal error correction technology – which had previously only been available in the PDX and X-Power amplifiers, is now integrated in V-Power mono amplifiers. The audio input signal is analysed, compared, and corrected twice dynamically as the signal is processed through the amplifier. The result is amplifiers with the widest frequency response, higher damping factor, and lowest noise in its class.

Exceptionally Simple Sound Upgrade

The V-Power's 4-channel speaker level inputs connect directly to any head unit, without the need for external converters. This makes the V-Power amplifiers ideal for upgrading factory and aftermarket systems. The flush mount controls make for easy installation. The terminal covers conveniently snap-on without the need for additional tools, to protect the wiring connections while creating a clean, finished appearance.

Proven Power

Each V-Power amplifier comes with its very own birth-sheet. V-Power amplifiers are tested and documented to show their true actual output.

FEATURES

Install

• Terminal Layout: Two-Sided
• Integrated Wire and Mounting Screw Terminals

General

• Amplifier Type: Class-D (Digital)
• Channel Design: 4/3/2-Channel
• Power Supply Design: DC-DC PWM Power Supply
• Power Supply: MOSFET
• Pre-Amp Stage: Discrete
• Final Outputs: Power MOSFET
• Crossover: Variable Lowpass & Highpass Filter
• Gain Control: Continuously Adjustable Gain Control
• Bass EQ
• Remote Turn On: Remote Sensing Function (for Speaker Level Input)
• Low-impedance Possibility
• Current Protection: Over-Current, Over-Voltage, Under-Voltage and Thermal Protection
• Board Circuitry: S.T.A.R. Circuit
• RCA Output: Non-Fading Pre-Amp Output (4 Volts)
• Speaker-Level Inputs: 4-channel Speaker Level Inputs
• Power Indicator: Top Mounted Blue LED Power Indicator
• Thermal Control: Multi-stage Power Limits

SPECIFICATIONS

Max Power Output Ratings

• Total Max Power: 640 W

RMS Power Ratings

• Per channel into 4 Ohms: 50W RMS x 4 (14.4V at <1% THD+N)
• Per channel into 2 Ohms: 75W RMS x 4 (14.4V at <1% THD+N)

Sound Tuning

• Crossover Frequency (LPF/HPF): 50Hz-400Hz , -12dB/oct.
• EQ (Equalizer): Bass EQ (fc=50Hz) 0 to +12dB for CH-3/4

Dimensions

• Foot Print (WxHxD) mm: 200 x 55 x 200 mm
• Heat Sink (WxHxD) mm: 165 x 55 x 200 mm

General

• Power Requirements: 14.4 V.DC (11-16V allowable)
• Input Sensitivity (RCA Input): 0.2 - 4.0 V
• Input Sensitivity (Speaker Level Input): 0.5 - 10 V
• Input Impedance: >10k ohms
• Frequency Response (+0, -1dB: 1W into 4 Ohms) for Subwoofer: 20Hz-20kHz
• THD+N (10W into 4 Ohms): 0.03 %
• THD+N (10W into 2 Ohms): 0.05 %
• THD+N (Rated Power into 4 Ohms): 0.08 %
• THD+N (Rated Power into 2 Ohms): 0.1 %
• Damping Factor (10W into 4 Ohms at 100Hz): >90
• Signal to Noise (1W into 4 Ohms): >81 dB
• Signal to Noise (Rated Power into 4 Ohms): >98 dB
• Weight: 1.7 kg

SPEAKER & RCA INPUTS

VERSATILE X-OVER

HIGH POWER/SIZE RATIO

ULTRA-COMPACT

ALPINE MRV-V500

4 Channel + Mono Digital V-Power Amplifier
Tens of thousands have relied on V-Power amplifiers for dependable, quality power. Now in their fourth generation, V-Power amplifiers carry on this heritage and prove that playing strong never looked our sounded better. Yes, it is possible to improve upon a good thing.

Proven Power

Each V-Power amplifier comes with its very own birth-sheet. V-Power amplifiers are tested and documented to show their true actual output.

Raising the Bar

The new V-Power products are now Class D digital amplifiers, resulting in a huge efficiency gain versus their predecessors without draining your battery or your pockets. Class-D provides continuous clean power to your speakers, operating at 80% efficiency far greater than conventional Class A or B amplifiers. Translation: Enjoy cleaner bass, even during extreme power demands.

Big Power, Small Package

V-Power amplifiers are known for their compact size, but don’t underestimate their power capacity. Although they have a 40% smaller footprint than their predecessors, they produce the same amount of power as before. Get the power you need, even if you have limited installation space.

Non Shut-Down Design

Even if you pound your music for a long time, these amps won’t shut down. They use a Thermal Management Processor to make sure the heat level never gets too high. No distortion, no interruptions!

SPECIFICATIONS

Max Power Output Ratings

• Total Max Power: 1100 W
• RMS Power Ratings
• Per channel into 4 Ohms: CH 1-4 (@14.4V ≤1%THD+N) 40W x 4
• Per channel into 4 Ohms: Subwoofer (@14.4V ≤1%THD+N) 150W x 1
• Per channel into 2 Ohms: CH 1-4 (@14.4V ≤1%THD+N) 60W x 4
• Per channel into 2Ohms: Subwoofer (@14.4V ≤1%THD+N) 250W x 1
• Bridged into 4ohms, 14.4V (@14.4V ≤1%THD+N) 120W RMS x 2

Sound Tuning

• Crossover (CH-1/2 and CH-3/4, HPF): 50 - 400 Hz , -12 dB/oct.
• Crossover (Subwoofer, LPF): 50 - 400 Hz, -24 dB/oct.
• Equalizer (Bass EQ): 0 to +12dB (Subwoofer, fc=50Hz) Variable

Dimensions

• Heat Sink (WxHxD) mm: 244.5 x 55 x 219 mm

General

• Power Requirements: 14.4 V.DC (11-16V allowable)
• Input Sensitivity Subwoofer (RCA Input): 0.2 - 4.0 V
• Input Sensitivity CH 1-4 (RCA Input): 0.2 - 4.0 V
• Input Impedance: >10k Ohms
• Frequency Response Subwoofer (+0, -3dB: 1W into 4 ohms): 10Hz - 400Hz
• Frequency Response CH 1-4 (+0, -3dB: 1W into 4 ohms): 10Hz - 45kHz
• Frequency Response Subwoofer (+0, -1dB: 1W into 4 ohms): 20Hz - 300Hz
• Frequency Response CH 1-4 (+0, -1dB: 1W into 4 ohms): 20Hz - 20kHz
• THD+N (10W into 4 Ohms): ≤ 0.02%
• THD+N (10W into 2 Ohms): ≤ 0.03%
• THD+N (Rated Power into 4 Ohms): ≤ 0.07%
• THD+N (Rated Power into 2 Ohms): ≤ 0.09%
• Damping Factor Subwoofer (10W into 4 Ohms at 100Hz): > 500
• Damping Factor CH 1-4 (10W into 4 Ohms at 100Hz): > 90
• Signal to Noise (1W into 4 Ohms): > 81 dB
• Signal to Noise CH 1-4 (Rated Power into 4 Ohms): > 98 dB
• Signal to Noise Subwoofer (Rated Power into 4 Ohms): > 104 dB
• Weight: 2.57 kg   

D CLASS MONO AMPLIFIER

HERTZ HI-ENERGY HDP5

D CLASS FIVE-CHANNEL AMPLIFIER